Everbuild 407 Mortar Stain Remover Building Products Surface Treatments 5L

£9.9
FREE Shipping

Everbuild 407 Mortar Stain Remover Building Products Surface Treatments 5L

Everbuild 407 Mortar Stain Remover Building Products Surface Treatments 5L

RRP: £99
Price: £9.9
£9.9 FREE Shipping

In stock

We accept the following payment methods

Description

Wall Mesh Membrane can be used to form a barrier between the salts in the wall and the new wall covering How to Treat Salting on Plaster For more stubborn stains, you could use a degreasing agent or engine cleaning fluid such as Gunk, but always test a small inconspicuous area first for adverse reactions. There is a treatment for efflorescence called Salt Neutraliser which you can buy from most DIY stores. The idea is to stop the remaining salts reacting with water and thereby preventing efflorescence forming. Proprietary rust removers such as RCI and Bero are very good * on the right substrate *. RCI, in particular, seems very good on crystalline stone (eg: granite) and uncoloured concrete.

However this is a different problem to efflorescence (also known as "salting"). You can read more about spalling in our project on freeze/thaw damage. Repeat application for extremely stubborn stains. finally flood treated areas with cold water after use. The Everbuild mortar stain remover is comprised of a fast-acting formula designed to remove mortar and cement stains from a range of surfaces. Once your efflorescence issues have been fully cured the next job is to repair any damage that’s been caused by it. Damaged Wall Plaster – How to Rectify Where this is the case the salts can be brushed off the wall and they should not re-occur. However, in cases where efflorescence is caused by a water leak, for instance where lead flashing is damaged, or masonry joints are missing, thereby allowing water to continuously enter the construction material, then efflorescence will continue to form.If used internally, extreme care must be taken and thorough ventilation provided as fumes can cause damage to sensitive surfaces.

A further handy tip for heavy staining is to pre-wash the affected paving with "OxiClean", a product more normally associated with domestic laundry. Once the Salt Neutraliser is fully dry you can redecorate your wall using paint or wallpaper. It is also useful to note that if you are going to paint the area then you may want to use a stain and damp primer before adding your top coat. The stain and damp primer will ensure that no tide marks or marks or any kind will reappear on the surface at any point in the future This water will find its way out of the wall through evaporation leaving the salts behind. The salts can be brushed off, but they frequently re-occur and damage the décor again. The most effective treatment for efflorescence and free lime staining on external wall surfaces is time as the natural weathering of the surface will remove the staining if you are patient. If it is efflorescence – other causes of white patches should be investigated and ruled out (see what is efflorescence above).

This still applies for deliveries out of our local area but please note that we use independent carriers so be aware that there may be external factors which we cannot control (e.g Far out postcodes or local traffic situations) Materials delivered direct from the manufacturer. After 3 – 6 hours, rinse with plenty of clean water. If traces remain after a couple of days, repeat the process. Stain and Damp Seal Paints dry and cure much faster than normal paints which prevents the stain forming through the paint In this situation you need to find the cause and repair it. You can buy Salt Neutraliser treatment (pictured below) and this is covered further in our How To Treat Efflorescence section. With the advent of smaller, portable blasting kit, some specialist contractors are willing to clean areas of, say, under 15m² for a couple of hundred quid (northern England prices -probably not applicable in that London). Obviously larger areas cost more, but for two hundred quid, clean paving worth in excess of 400 quid in terms of replacement (27 quid/m²), is perfectly possible.

Ensure that the surface to be treated is completely free from dust and dirt before application. If necessary, wash with LTP Power Stripperdiluted 1:10 with water. Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour Sand down the area to remove all the salts from the wall, when you are doing this wear a mask to avoid breathing in the dust and wear gloves to protect your skin. You will usually find that the salts will come away easily with medium or fine sandpaper. However in severe cases start with coarse grit sandpaper and down to fine one, to make sure you have a sound surface before you redecorate

Please note that given the current circumstances alot of carrier companies are struggling to keep up with demand and although we do book these deliveries as next day services, the carriers cannot always fulfil these and an extra day may be required. In the photie above, old, reclaimed yorkstone flags from the streets of East Lancashire have been brought up like new by blasting with grit to remove all dirt and surface staining. One of the modern, portable surface blasters used to clean badly stained pavements To find Ready Mixed colours, search "ready mixed" or select the Ready Mixed 'colour chart'. To see Tinted colours select a colour chart such as RAL, BS, NCS, etc. or search for a colour/hue to see available or related options. The sooner an oil stain is treated, the more likely it is to be removed. Use a cloth to soak-up any oil droplets on the surface, but don't smear or rub the oil into the surface. Fresh oil stains can be soaked up by proprietary absorbent materials or even some of the clay-based cat litters, cornflour or talcum powder. Any residue remaining after treating with an absorbent agent can sometimes be removed or ameliorated by scrubbing with a detergent and brush before washing down with water. It may take several attempts for this to work. Clean oil will generally soak into the paving and there will be little evidence of its presence after a few weeks. Dirty oil can be very difficult, if not impossible to completely remove. If the paint is still fresh, soak up as much as possible, being careful not to wipe and further spread the paint. You can then use a solvent on the area before washing with warm water and detergent. Remember to follow any safety instructions on the paint remover or solvent.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop