Rapid Racer Products RRP ProGuard Front Mountain Bike Mudguard

FREE Shipping

Rapid Racer Products RRP ProGuard Front Mountain Bike Mudguard

Rapid Racer Products RRP ProGuard Front Mountain Bike Mudguard

RRP: £29.95
Price: £14.975
£14.975 FREE Shipping

In stock

We accept the following payment methods


The 'T' shape clamping points on the arms are designed to wrap around the fork leg providing a better and neater fit. The front of the mudguard is designed to offer increased protection for higher speeds without spoiling the look of the mudguard. The wider curve with flat rear end offers maximum protection and frame clearance compared to a simple symmetrical curve SIZING FRONT SUSPENSION: 80mm - 125mm - STANDARD FRONT SUSPENSION: 130mm - 200mm - LARGE REAR MUDGUARD

Important - If you have a brace between the seatstays - you must attach at least one cable tie to it if you don't have a brace between the seatstays - you must use 3 cable ties on each arm Chain reaction Cycles and CRC are trading names of Wiggle Ltd (In Administration) registered in the United Kingdom at 1000 Lakeside, Suite 310, Third Floor N E Wing, Portsmouth, Hampshire, PO6 3EN, We have tested the following chemicals to use on our ProGuards to keep them looking great and shedding mud:

Squeeze the side wings of the mudguard hard and slide under the fork brace from the rear with the wheel and tyre still in place You can also change the height of the mudguard by 6mm through the slots for more clearance. NOTE: Highest position offers the most stability with the best mud clearance The best guards are the longest and work at all speeds. If you’re riding slowly, mud comes off the trailing edge of the tyre and is thrown upwards, but as speed increases it’s thrown further forward and you eventually ride into this spray. Having a mudguard that covers the full arc of mud trajectory is the best option. RapidRacerProducts Ltd accepts no liability for any damage / injury caused due to improper fitting / use of our products

Select the correct bolts for your fork (details below) and run these into the threads WITHOUT the mudguard which will 'PRIME' and clean the threads before fitting, this part is important (YOU MAY NEED TO RE-TAP THE THREADS IF DEBRIS / PAINT IS LEFT IN THE THREADS FROM THE MANUFACTURE OF THE FORKS) BOLTS: FOX = M3 (2 bolts) | OHLINS = M4 (3 bolts) | SR SUNTOUR = M6 ( *1 bolt) Slots and holes for easy installation with cable ties (included) or Velcro straps (sold separately)long 24g (without cable ties) MAIN DISTRIBUTORS UK EXTRA UK FRANCE TRIBE SPORT GROUP NORWAY DELER AS REST OF EU NOW COMPANY USA AND CANADA RECIPROCATORS Forks: This direct mount mudguard is designed for the forks listed below ONLY IF THEY HAVE Threaded holes in the rear of the fork brace Fits Fox 32, 34, 36, 38, *40 (2021) 49 Slide the guard into position WITH THE WHEEL IN PLACE, you may need to squeeze the sides of the guard as you do so to get it through the sear stays

Then feed cable ties through teh sames holes from the rear to the front (you must use min 5 cable ties to ensure the guard is secure) COMPATIBILITY WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre FORKS: All forks including Boost forks (except reverse arch) TRAVEL: Any travel We offer the longer MAX PROTECTION version to be the best protection in the world, this version is 68mm longer at the rear. No other mudguard offers more protection MATERIAL It fits in under a minute and it'll do far more justice to your posh rig than that manky old bit of inner tube DirtI have been using the RRP ProGuard on a few mountain bikes for several months. The performance has been excellent, with a vast improvement in the amount of spray and mud that comes off the front wheel reaching the face and body with the most noticeable area when riding at higher speeds where mud can spray out in front, which you would normally ride into it. The ENDUROGUARD is designed as a FRONT or REAR mudguard and has been specifically adapted to do both jobs extremely well ADDITIONAL FEATURES Use the Allen key provided to screw the bolts in EVENLY a bit each side, go gentle to start off to ensure you DON'T CROSS THREAD THEM, stop once it's pulled together so you can still move it INSPECT BEFORE YOU RIDE: DO NOT USE IF DAMAGED IN ANY WAY AS CONTINUED USE MAY LEAD TO FAILURE OR INJURY

You have a choice of snap-off holes for the front fork brace, narrow holes for normal forks and if needed wider holes for BOOST forks Finance is subject to application, financial circumstances and borrowing history. Performance Cycling Limited FRN: 720557 trading as Tredz are authorised and regulated by the Financial Conduct Authority. We are a credit broker not a lender – credit is subject to status and affordability and is provided by Mitsubishi HC Capital UK PLC. Terms & Conditions Apply. As a result of achieving the above properties it means that the surface layer is soft and will scratch easily, you must also be careful about putting any chemicals onto the surface as it may tarnish the finish. That said we have tested and can recommend the following chemicals to use: The ProGuard - BOLT ON is our direct mount front mountainbike mudguard designed for big spray and mud protection (DISC BRAKE ONLY)Pull the top straps to stretch the Neoguard, don't worry about stretching the eyelets as it's re-enforced eyelets are designed to stretch, once fitted it should be taught. The stretch reduces the gathering of the guard when the fork compresses. Finally, YOU MUST CUT OFF THE EXCESS HOOK AND LOOP STRAPS AFTER FITTING

  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns


Address: UK
All products: Visit Fruugo Shop